Fingerprint Reader Turnstile Barrier Gate , Acrylic Flap Barrier
Flap Barrier, half height turnstile, waist height turnstile, falp
turnstile, turnstile, turnstiles, access control turnstile, access
control barrier, sensor gate, sensor barrier, panel barrier, wing
barrier, wing gate, wing turnstile, speed gate, access control
system, perimeter protection barrier.
-> Single-core mechanism: RNCF1088
The flap barrier only equipped with single-core in the cabinet,
usually be used in single lane or multi-lane applications.
->Dual-core mechanism: RNCF1088S
The flap barrier equipped with independent dual-core in the
cabinet, usually be used in multi-lane applications.
304# Stainless Steel (default), 201# or 316# Stainless Steel or
Thickness of ply
brushed surface, polishing surface or anti-fingerprint surface
Material of flap
different color Acrylic flap available or Red Soft flapper optional
Stretching-out flap length
The inductive card reader dimension
equipped with the standard mounting brackets or tailor.
Germany technological motor
DC Brush motor
Opening / closing time
The time required to running state after power on
Automatic reset time after the failure
Mean time to failure
min. 5 000 000
-10℃ ~ +70℃
less than 95% not condensed
Indoor/Outdoor (with rain-tent cover)
relay dry contact signal; +12V level signal and pulse width
>100ms, DC12V pulse signal
RS232/ RS485 electric standard, communications range≤1200m.
Available to connect with external CAN BUS and Ethernet
STANDARD FEATURES & FUNCTIONS:
(1). The turnstile system can easily integrates with the 3rd party equipment, such as Biometric reader, consumption system, ESD
system and access control system etc.
(2). Operation model: Both directions can be set as controlled mode
or free mode, two or one direction can be controlled by switch-
button or access controller.
(3). Automatic check fault and alarm prompt function: to convenient
for users to maintain and use.
(4). The running status of device can be set up through pressing
the built-in small keyboard of the main control board.
(5). The device is locked until a valid open signal is received.
(6). Infrared detection sensors: The device uses several infrared
sensors transmitter and receiver type. The sensors are positioned
at two different heights to defend against people trying to
roll/crawl through the lane without being detected. The sensors are
positioned at approximately knee height and waist height. The
sensors can detect abnormal access and turnstile system will stay
(7). Anti-pinch function: Auto-alarm will activate for unauthorized
pedestrian movement and tailgating. The barrier uses several photo
sensors to prevent turnstile closure on a person while inside the
(8). Reset automatically function: “Go” signal will be cancelled if
passage through is not completed within pre-set time. The standard
default is 10 seconds (time adjustable 1s ~ 60s) by changing
parameter of main control board). Also when power off, it will be
opened the gates automatically. When the power is on again, the
gates can also close automatically.
(9). Emergency-escape function: When power off, it will be opened
the gates automatically to meet the request of fire protection.
Also the gates will open by pressing the emergency button which can
be remote-controlled whether the power is on or not. (Optional).
(10). LED indicator function: Traffic lights on both sides of the
turnstile barrier are the indicator of access status, When the
traffic lights show green, it means to pass and the red light means
no-entry. The traffic lights on both sides can be set to indicate
access for left or right or bi-direction.
(11). Remote control and management function: Through the
management computer to realize remote control and management.
(12). Streamline design that utilizes shared cabinets for
(13). The entire system runs smoothly, with a small noise and free
of mechanical impact.
(14). With normally open & normally closed working mode.
(15). Approved CE certificate.
Shenzhen Rona Intelligent Technology Co., Ltd is a Chinese
manufacturing firm located in Shenzhen. When you are ready to find
out how we can service your needs, use the information listed here
to reach our sales and service office. Monday to Friday: 8:30am -
6:00pm (UTC/GMT +8). We look forward to hearing from you.
Head office: A603, 6F, Yousong Technology Building, E Ring 1st Rd,
Loghua Town, Bao'an, Shenzhen, China, 518109
Factory: 3F&4F, Building C, Longlian Industrial Zone, Zhonghua
Rd, Longhuan Town, Bao'an, Shenzhen, China, 518109
Contact Person: Ms. Sophia Wey
Tel: +86-755-88853586 ext 8039
Fax: +86-755-88853586 ext 8002